This table provides a comprehensive list of commands and the specific command errors that can be returned by the ErrorDescription when a command is unsuccessful.

	ErrorDescription
Connection Commands
Open_Device_Connection
Close_Device_Connection
Data Link Commands
Slave_Activity_Inquiry
Set Commands
Set_Sensor_Identification_Number	"Invalid Serial Number"
Set_Unit_Code	"Invalid Unit Code"
Set_Decimal_Point	"Invalid Decimal Point"
Set_Calibration_Register	"Invalid Register"
Set_Loading_Point	"Invalid Loading Point"
Set_Load_of_Loading_Point	"Invalid Loading Point" "Invalid Load Value"
Set_Sensor_Configuration	"Invalid Sensor Configuration"
Set_Load_Switch	"Invalid Simulated Load"
Set_Number_of_Loading_Points	"Invalid Number Of Loading Points"
Set_ADC_Configuration	"Invalid Sampling Rate"
Set_ADC_Configuration2	"Invalid ADC Configuration"
Set_Average_Setting	"Invalid Average Setting"
Set_Voltage_Output	"Invalid Loading Point"
Set_Digital_Components
Set_Calibration_Mode
Set_Sensitivity	"Invalid Sensitivity"
Set_Bridge_Resistance	"Invalid Bridge Resistance"
Set_Direction	"Invalid Direction"
Set_Zero_Correction	"Invalid Type Of Calibration" "Invalid Point"
Set_Shunt_Value	"Invalid Shunt Value"
Set_Calibration_Code	"Invalid Calibration Code"
Set_Calibration_Day	"Invalid Calibration Day"
Set_Calibration_Month	"Invalid Calibration Month"
Set_Calibration_Year	"Invalid Calibration Year"
Set_Pulses_Per_Rotation	"Invalid Pulses Per Rotation"
Set_CrossTalk	"Invalid CrossTalk"
Set_Number_of_Active_Channels	"Invalid Number Of Active Channels"
Set_Type_of_Calibration	"Invalid Type Of Calibration"
Set_Active_Page_Number	"Invalid Active Page Number"
Set_Destination_MAC_Address
Set_Destination_IP_Address
Set_Destination_Port_Number	"Invalid Port Number"
Set_Source_IP_Address
Set_Source_Port_Number	"Invalid Port Number"
Reset_Angle
Get Commands
Get_Offset_Value
Get_Fullscale_Value
Normal_Data_Request
Fast_Data_Request	"Invalid Firmware Version"
Version_of_Board
Reset_Board
Get_Display_Page
Get_Internal_Register	"Invalid Register"
Get_Data_Logging	"Invalid Counter"
Get_Rotation_Values
Get_Device_Count
Get_Device_Serial_Number
Get_Loading_Point	"Invalid Type Of Calibration" "Invalid Point"
Get_Offset_Load
Get_Load_of_Loading_Point	"Invalid Point"
Get_Fullscale_Load
Get_Number_of_Loading_Points
Get_Output_Type
Get_Sensitivity
Get_Bridge_Resistance
Get_ADC_PGA_Setting
Get_ADC_Sampling_Rate_Setting
Get_Sensor_Identification_Number
Get_Unit_Code
Get_Direction
Get_Shunt_Value
Get_Decimal_Point
Get_Calibration_Code
Get_Calibration_Day
Get_Calibration_Month
Get_Calibration_Year
Get_Pulses_Per_Rotation
Get_Voltage_Output
Get_CrossTalk
Get_Number_of_Active_Channels
Get_Type_of_Calibration
Get_Active_Page_Number
Get_Destination_MAC_Address
Get_Destination_IP_Address
Get_Destination_Port_Number
Get_Source_MAC_Address
Get_Source_IP_Address
Get_Source_Port_Number
Get_Excitation
Get_Analog_Voltage_Output
Get_Gain_Switch
Get_Polarity
Get_Shunt_Resistor
Get_Sensor_Sensitivity
Get_Zero_Potentiometer
Get_Span_1_Potentiometer
Get_Span_2_Potentiometer
Get_Average_Setting
Get_Type_of_Board
Get_Hardware_Version
Get_Firmware_Version
Get_Firmware_Year
Get_Firmware_Month
Backup Commands
Create_Back_Up	"Invalid Page Number"
Restore_Back_Up	"Invalid Page Number"
Control Commands
Change_Battery_Enter
Change_Tare_Up
Change_Display_Back
Change_Reset_Left
Change_Menu
Change_Unit_Right
Change_Shunt_Exit
Change_Hold_Down
Debugging Commands
Read_Memory_Register	"Invalid Address"
Write_Memory_Register	"Invalid Address" "Invalid Data"
Read_EEPROM_Register	"Invalid Address"
Write_EEPROM_Register	"Invalid Address" "Invalid High Byte" "Invalid Low Byte"
Read_TEDS_Register	"Invalid High Address" "Invalid Low Address"
Write_TEDS_Register	"Invalid Data" "Invalid High Address" "Invalid Low Address"
Read_Channel_Register	"Invalid Address"
Write_Channel_Register	"Invalid Address" "Invalid Data"
Read_Page_Register	"Invalid Page Number"