Command Overview

This table provides a comprehensive list of commands and the model numbers that support each command. The Memory column indicates which commands write to the EEPROM of the USB device.

	ETH100	IDA100	IHH500	IPM650	USB100	USB110	USB120	USB200	USB210	USB215	USB220	USB230	USB240	USB320	USB410	USB520	USB530	Memory
Connection Commands
Open_Device_Connection	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Close_Device_Connection	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Data Link Commands
Slave_Activity_Inquiry	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Set Commands
Set_Sensor_Identification_Number	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Set_Unit_Code	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●	●
Set_Decimal_Point	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●	●
Set_Calibration_Register			●	●														●
Set_Loading_Point	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Set_Load_of_Loading_Point	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Set_Sensor_Configuration	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Set_Load_Switch	●	●	●	●	●	●	●	●	●	●	●	●						●
Set_Number_of_Loading_Points	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Set_ADC_Configuration	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●	●
Set_ADC_Configuration2	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Set_Average_Setting	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Set_Voltage_Output																●	●	●
Set_Digital_Components		●																●
Set_Calibration_Mode		●																●
Set_Sensitivity	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●	●
Set_Bridge_Resistance	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●	●
Set_Direction	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●	●
Set_Zero_Correction	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●	●
Set_Shunt_Value	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●	●
Set_Calibration_Code	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●	●
Set_Calibration_Day	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●	●
Set_Calibration_Month	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●	●
Set_Calibration_Year	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●	●
Set_Pulses_Per_Rotation															●	●	●	●
Set_CrossTalk													●			●	●	●
Set_Number_of_Active_Channels													●			●	●	●
Set_Type_of_Calibration													●			●	●	●
Set_Active_Page_Number													●			●	●	●
Set_Destination_MAC_Address	●																	●
Set_Destination_IP_Address	●																	●
Set_Destination_Port_Number	●																	●
Set_Source_IP_Address	●																	●
Set_Source_Port_Number	●																	●
Reset_Angle															●	●	●
Get Commands
Get_Offset_Value	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Get_Fullscale_Value	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Normal_Data_Request	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Fast_Data_Request	●	●				●	●		●	●	●	●	●	●	●	●	●
Version_of_Board	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Reset_Board	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Get_Display_Page			●	●
Get_Internal_Register			●	●
Get_Data_Logging			●	●
Get_Rotation_Values			●	●											●	●	●
Get_Device_Count	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Get_Device_Serial_Number	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Get_Loading_Point	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●
Get_Offset_Load	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●
Get_Load_of_Loading_Point	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●
Get_Fullscale_Load	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●
Get_Number_of_Loading_Points	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●
Get_Output_Type																●	●
Get_Sensitivity	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●
Get_Bridge_Resistance	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●
Get_ADC_PGA_Setting	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●
Get_ADC_Sampling_Rate_Setting	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●
Get_Sensor_Identification_Number	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●
Get_Unit_Code	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●
Get_Direction	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●
Get_Shunt_Value	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●
Get_Decimal_Point	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●
Get_Calibration_Code	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●
Get_Calibration_Day	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●
Get_Calibration_Month	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●
Get_Calibration_Year	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●
Get_Pulses_Per_Rotation															●	●	●
Get_Voltage_Output																●	●
Get_CrossTalk													●			●	●
Get_Number_of_Active_Channels													●			●	●
Get_Type_of_Calibration													●			●	●
Get_Active_Page_Number													●			●	●
Get_Destination_MAC_Address	●
Get_Destination_IP_Address	●
Get_Destination_Port_Number	●
Get_Source_MAC_Address	●
Get_Source_IP_Address	●
Get_Source_Port_Number	●
Get_Excitation		●
Get_Analog_Voltage_Output		●
Get_Gain_Switch		●
Get_Polarity		●
Get_Shunt_Resistor		●
Get_Sensor_Sensitivity		●
Get_Zero_Potentiometer		●
Get_Span_1_Potentiometer		●
Get_Span_2_Potentiometer		●
Get_Average_Setting	●	●			●	●	●	●	●	●	●	●	●	●	●	●	●
Get_Type_of_Board	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Get_Hardware_Version	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Get_Firmware_Version	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Get_Firmware_Year	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Get_Firmware_Month	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Backup Commands
Create_Back_Up	●	●				●	●		●	●	●	●	●	●	●	●	●	●
Restore_Back_Up	●	●				●	●		●	●	●	●	●	●	●	●	●	●
Control Commands
Change_Battery_Enter			●	●
Change_Tare_Up			●	●
Change_Display_Back			●	●
Change_Reset_Left			●	●
Change_Menu			●	●
Change_Unit_Right			●	●
Change_Shunt_Exit			●	●
Change_Hold_Down			●	●
Debugging Commands
Read_Memory_Register	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Write_Memory_Register	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Read_EEPROM_Register	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Write_EEPROM_Register	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Read_TEDS_Register			●	●
Write_TEDS_Register			●	●														●
Read_Channel_Register	●	●	●	●									●			●	●
Write_Channel_Register	●	●	●	●									●			●	●	●
Read_Page_Register													●

This table provides a comprehensive list of commands and the response of each command. The responses have been separated for commands that were successful and unsuccessful. If the command was sent and received successfully, then the response will typically be either 0 or a number in a given range. Please refer to the sections related to a specific command for more information. If the command was sent and received unsuccessfully, then the response will be “Error” and the ErrorDescription will be updated. Please refer to the Common Command Errors or Specific Command Errors for more information.

This table provides a comprehensive list of commands and the specific command errors that can be returned by the ErrorDescription when a command is unsuccessful.

	Successful Response	Unsuccessful Response
Connection Commands
Open_Device_Connection	N/A	N/A
Close_Device_Connection	N/A	N/A
Data Link Commands
Slave_Activity_Inquiry	0	Error
Set Commands
Set_Sensor_Identification_Number	0	Error
Set_Unit_Code	0	Error
Set_Decimal_Point	0	Error
Set_Calibration_Register	0	Error
Set_Loading_Point	0	Error
Set_Load_of_Loading_Point	0	Error
Set_Sensor_Configuration	0	Error
Set_Load_Switch	0	Error
Set_Number_of_Loading_Points	0	Error
Set_ADC_Configuration	0	Error
Set_ADC_Configuration2	0	Error
Set_Average_Setting	0	Error
Set_Voltage_Output	0	Error
Set_Digital_Components	0	Error
Set_Calibration_Mode	0	Error
Set_Sensitivity	0	Error
Set_Bridge_Resistance	0	Error
Set_Direction	0	Error
Set_Zero_Correction	0	Error
Set_Shunt_Value	0	Error
Set_Calibration_Code	0	Error
Set_Calibration_Day	0	Error
Set_Calibration_Month	0	Error
Set_Calibration_Year	0	Error
Set_Pulses_Per_Rotation	0	Error
Set_CrossTalk	0	Error
Set_Number_of_Active_Channels	0	Error
Set_Type_of_Calibration	0	Error
Set_Active_Page_Number	0	Error
Set_Destination_MAC_Address	0	Error
Set_Destination_IP_Address	0	Error
Set_Destination_Port_Number	0	Error
Set_Source_IP_Address	0	Error
Set_Source_Port_Number	0	Error
Reset_Angle	0	Error
Get Commands
Get_Offset_Value	Number	Error
Get_Fullscale_Value	Number	Error
Normal_Data_Request	Number	Error
Fast_Data_Request	String	Error
Version_of_Board	0	Error
Reset_Board	0	Error
Get_Display_Page	0	Error
Get_Internal_Register	Number	Error
Get_Data_Logging	0	Error
Get_Rotation_Values	0	Error
Get_Device_Count	Number	Error
Get_Device_Serial_Number	Number	Error
Get_Loading_Point	Number	Error
Get_Offset_Load	Number	Error
Get_Load_of_Loading_Point	Number	Error
Get_Fullscale_Load	Number	Error
Get_Number_of_Loading_Points	Number	Error
Get_Output_Type	Number	Error
Get_Sensitivity	Number	Error
Get_Bridge_Resistance	Number	Error
Get_ADC_PGA_Setting	Number	Error
Get_ADC_Sampling_Rate_Setting	Number	Error
Get_Sensor_Identification_Number	Number	Error
Get_Unit_Code	Number	Error
Get_Direction	Number	Error
Get_Shunt_Value	Number	Error
Get_Decimal_Point	Number	Error
Get_Calibration_Code	Number	Error
Get_Calibration_Day	Number	Error
Get_Calibration_Month	Number	Error
Get_Calibration_Year	Number	Error
Get_Pulses_Per_Rotation	Number	Error
Get_Voltage_Output	Number	Error
Get_CrossTalk	Number	Error
Get_Number_of_Active_Channels	Number	Error
Get_Type_of_Calibration	Number	Error
Get_Active_Page_Number	Number	Error
Get_Destination_MAC_Address	0	Error
Get_Destination_IP_Address	0	Error
Get_Destination_Port_Number	0	Error
Get_Source_MAC_Address	0	Error
Get_Source_IP_Address	0	Error
Get_Source_Port_Number	0	Error
Get_Excitation	Number	Error
Get_Analog_Voltage_Output	Number	Error
Get_Gain_Switch	Number	Error
Get_Polarity	Number	Error
Get_Shunt_Resistor	Number	Error
Get_Sensor_Sensitivity	Number	Error
Get_Zero_Potentiometer	Number	Error
Get_Span_1_Potentiometer	Number	Error
Get_Span_2_Potentiometer	Number	Error
Get_Average_Setting	Number	Error
Get_Type_of_Board	Number	Error
Get_Hardware_Version	Number	Error
Get_Firmware_Version	Number	Error
Get_Firmware_Year	Number	Error
Get_Firmware_Month	Number	Error
Backup Commands
Create_Back_Up	0	Error
Restore_Back_Up	0	Error
Control Commands
Change_Battery_Enter	0	Error
Change_Tare_Up	0	Error
Change_Display_Back	0	Error
Change_Reset_Left	0	Error
Change_Menu	0	Error
Change_Unit_Right	0	Error
Change_Shunt_Exit	0	Error
Change_Hold_Down	0	Error
Debugging Commands
Read_Memory_Register	Number	Error
Write_Memory_Register	0	Error
Read_EEPROM_Register	Number	Error
Write_EEPROM_Register	0	Error
Read_TEDS_Register	Number	Error
Write_TEDS_Register	0	Error
Read_Channel_Register	Number	Error
Write_Channel_Register	0	Error
Read_Page_Register	0	Error

This table provides a comprehensive list of commands and the common command errors that can be returned by the ErrorDescription when a command is unsuccessful. Please refer to the Specific Command Errors for additional errors that can be returned by the ErrorDescription.

	"Timeout Error"	"Packet Number Error"	"Packet Size Error"	"Packet Frame Error"	"Packet Command Error"	"Command Number Error"	"Command Error"	"End Of Packet Error"	"TEDS Error"	"Invalid Type of Board"
Connection Commands
Open_Device_Connection
Close_Device_Connection
Data Link Commands
Slave_Activity_Inquiry	●	●	●	●	●	●	●	●	●
Set Commands
Set_Sensor_Identification_Number	●	●	●	●	●	●	●	●	●	●
Set_Unit_Code	●	●	●	●	●	●	●	●	●	●
Set_Decimal_Point	●	●	●	●	●	●	●	●	●	●
Set_Calibration_Register	●	●	●	●	●	●	●	●	●	●
Set_Loading_Point	●	●	●	●	●	●	●	●	●	●
Set_Load_of_Loading_Point	●	●	●	●	●	●	●	●	●	●
Set_Sensor_Configuration	●	●	●	●	●	●	●	●	●	●
Set_Load_Switch	●	●	●	●	●	●	●	●	●	●
Set_Number_of_Loading_Points	●	●	●	●	●	●	●	●	●	●
Set_ADC_Configuration	●	●	●	●	●	●	●	●	●	●
Set_ADC_Configuration2	●	●	●	●	●	●	●	●	●	●
Set_Average_Setting	●	●	●	●	●	●	●	●	●	●
Set_Voltage_Output	●	●	●	●	●	●	●	●	●	●
Set_Digital_Components	●	●	●	●	●	●	●	●	●	●
Set_Calibration_Mode	●	●	●	●	●	●	●	●	●	●
Set_Sensitivity	●	●	●	●	●	●	●	●	●	●
Set_Bridge_Resistance	●	●	●	●	●	●	●	●	●	●
Set_Direction	●	●	●	●	●	●	●	●	●	●
Set_Zero_Correction	●	●	●	●	●	●	●	●	●	●
Set_Shunt_Value	●	●	●	●	●	●	●	●	●	●
Set_Calibration_Code	●	●	●	●	●	●	●	●	●	●
Set_Calibration_Day	●	●	●	●	●	●	●	●	●	●
Set_Calibration_Month	●	●	●	●	●	●	●	●	●	●
Set_Calibration_Year	●	●	●	●	●	●	●	●	●	●
Set_Pulses_Per_Rotation	●	●	●	●	●	●	●	●	●	●
Set_CrossTalk	●	●	●	●	●	●	●	●	●	●
Set_Number_of_Active_Channels	●	●	●	●	●	●	●	●	●	●
Set_Type_of_Calibration	●	●	●	●	●	●	●	●	●	●
Set_Active_Page_Number	●	●	●	●	●	●	●	●	●	●
Set_Destination_MAC_Address	●	●	●	●	●	●	●	●	●	●
Set_Destination_IP_Address	●	●	●	●	●	●	●	●	●	●
Set_Destination_Port_Number	●	●	●	●	●	●	●	●	●	●
Set_Source_IP_Address	●	●	●	●	●	●	●	●	●	●
Set_Source_Port_Number	●	●	●	●	●	●	●	●	●	●
Reset_Angle	●	●	●	●	●	●	●	●	●	●
Get Commands
Get_Offset_Value	●	●	●	●	●	●	●	●	●
Get_Fullscale_Value	●	●	●	●	●	●	●	●	●
Normal_Data_Request	●	●	●	●	●	●	●	●	●
Fast_Data_Request	●	●	●	●	●	●	●	●	●	●
Version_of_Board	●	●	●	●	●	●	●	●	●
Reset_Board	●	●	●	●	●	●	●	●	●
Get_Display_Page	●	●	●	●	●	●	●	●	●
Get_Internal_Register	●	●	●	●	●	●	●	●	●
Get_Data_Logging	●	●	●	●	●	●	●	●	●
Get_Rotation_Values	●	●	●	●	●	●	●	●	●
Get_Device_Count
Get_Device_Serial_Number
Get_Loading_Point	●	●	●	●	●	●	●	●	●	●
Get_Offset_Load	●	●	●	●	●	●	●	●	●	●
Get_Load_of_Loading_Point	●	●	●	●	●	●	●	●	●	●
Get_Fullscale_Load	●	●	●	●	●	●	●	●	●	●
Get_Number_of_Loading_Points	●	●	●	●	●	●	●	●	●	●
Get_Output_Type	●	●	●	●	●	●	●	●	●	●
Get_Sensitivity	●	●	●	●	●	●	●	●	●	●
Get_Bridge_Resistance	●	●	●	●	●	●	●	●	●	●
Get_ADC_PGA_Setting	●	●	●	●	●	●	●	●	●	●
Get_ADC_Sampling_Rate_Setting	●	●	●	●	●	●	●	●	●	●
Get_Sensor_Identification_Number	●	●	●	●	●	●	●	●	●	●
Get_Unit_Code	●	●	●	●	●	●	●	●	●	●
Get_Direction	●	●	●	●	●	●	●	●	●	●
Get_Shunt_Value	●	●	●	●	●	●	●	●	●	●
Get_Decimal_Point	●	●	●	●	●	●	●	●	●	●
Get_Calibration_Code	●	●	●	●	●	●	●	●	●	●
Get_Calibration_Day	●	●	●	●	●	●	●	●	●	●
Get_Calibration_Month	●	●	●	●	●	●	●	●	●	●
Get_Calibration_Year	●	●	●	●	●	●	●	●	●	●
Get_Pulses_Per_Rotation	●	●	●	●	●	●	●	●	●	●
Get_Voltage_Output	●	●	●	●	●	●	●	●	●	●
Get_CrossTalk	●	●	●	●	●	●	●	●	●	●
Get_Number_of_Active_Channels	●	●	●	●	●	●	●	●	●	●
Get_Type_of_Calibration	●	●	●	●	●	●	●	●	●	●
Get_Active_Page_Number	●	●	●	●	●	●	●	●	●	●
Get_Destination_MAC_Address	●	●	●	●	●	●	●	●	●	●
Get_Destination_IP_Address	●	●	●	●	●	●	●	●	●	●
Get_Destination_Port_Number	●	●	●	●	●	●	●	●	●	●
Get_Source_MAC_Address	●	●	●	●	●	●	●	●	●	●
Get_Source_IP_Address	●	●	●	●	●	●	●	●	●	●
Get_Source_Port_Number	●	●	●	●	●	●	●	●	●	●
Get_Excitation	●	●	●	●	●	●	●	●	●	●
Get_Analog_Voltage_Output	●	●	●	●	●	●	●	●	●	●
Get_Gain_Switch	●	●	●	●	●	●	●	●	●	●
Get_Polarity	●	●	●	●	●	●	●	●	●	●
Get_Shunt_Resistor	●	●	●	●	●	●	●	●	●	●
Get_Sensor_Sensitivity	●	●	●	●	●	●	●	●	●	●
Get_Zero_Potentiometer	●	●	●	●	●	●	●	●	●	●
Get_Span_1_Potentiometer	●	●	●	●	●	●	●	●	●	●
Get_Span_2_Potentiometer	●	●	●	●	●	●	●	●	●	●
Get_Average_Setting	●	●	●	●	●	●	●	●	●	●
Get_Type_of_Board	●	●	●	●	●	●	●	●	●
Get_Hardware_Version	●	●	●	●	●	●	●	●	●
Get_Firmware_Version	●	●	●	●	●	●	●	●	●
Get_Firmware_Year	●	●	●	●	●	●	●	●	●
Get_Firmware_Month	●	●	●	●	●	●	●	●	●
Backup Commands
Create_Back_Up	●	●	●	●	●	●	●	●	●
Restore_Back_Up	●	●	●	●	●	●	●	●	●
Control Commands
Change_Battery_Enter	●	●	●	●	●	●	●	●	●	●
Change_Tare_Up	●	●	●	●	●	●	●	●	●	●
Change_Display_Back	●	●	●	●	●	●	●	●	●	●
Change_Reset_Left	●	●	●	●	●	●	●	●	●	●
Change_Menu	●	●	●	●	●	●	●	●	●	●
Change_Unit_Right	●	●	●	●	●	●	●	●	●	●
Change_Shunt_Exit	●	●	●	●	●	●	●	●	●	●
Change_Hold_Down	●	●	●	●	●	●	●	●	●	●
Debugging Commands
Read_Memory_Register	●	●	●	●	●	●	●	●	●
Write_Memory_Register	●	●	●	●	●	●	●	●	●
Read_EEPROM_Register	●	●	●	●	●	●	●	●	●
Write_EEPROM_Register	●	●	●	●	●	●	●	●	●
Read_TEDS_Register	●	●	●	●	●	●	●	●	●
Write_TEDS_Register	●	●	●	●	●	●	●	●	●
Read_Channel_Register	●	●	●	●	●	●	●	●	●
Write_Channel_Register	●	●	●	●	●	●	●	●	●
Read_Page_Register	●	●	●	●	●	●	●	●	●

This table provides a comprehensive list of commands and the specific command errors that can be returned by the ErrorDescription when a command is unsuccessful.

	ErrorDescription
Connection Commands
Open_Device_Connection
Close_Device_Connection
Data Link Commands
Slave_Activity_Inquiry
Set Commands
Set_Sensor_Identification_Number	"Invalid Serial Number"
Set_Unit_Code	"Invalid Unit Code"
Set_Decimal_Point	"Invalid Decimal Point"
Set_Calibration_Register	"Invalid Register"
Set_Loading_Point	"Invalid Loading Point"
Set_Load_of_Loading_Point	"Invalid Loading Point" "Invalid Load Value"
Set_Sensor_Configuration	"Invalid Sensor Configuration"
Set_Load_Switch	"Invalid Simulated Load"
Set_Number_of_Loading_Points	"Invalid Number Of Loading Points"
Set_ADC_Configuration	"Invalid Sampling Rate"
Set_ADC_Configuration2	"Invalid ADC Configuration"
Set_Average_Setting	"Invalid Average Setting"
Set_Voltage_Output	"Invalid Loading Point"
Set_Digital_Components
Set_Calibration_Mode
Set_Sensitivity	"Invalid Sensitivity"
Set_Bridge_Resistance	"Invalid Bridge Resistance"
Set_Direction	"Invalid Direction"
Set_Zero_Correction	"Invalid Type Of Calibration" "Invalid Point"
Set_Shunt_Value	"Invalid Shunt Value"
Set_Calibration_Code	"Invalid Calibration Code"
Set_Calibration_Day	"Invalid Calibration Day"
Set_Calibration_Month	"Invalid Calibration Month"
Set_Calibration_Year	"Invalid Calibration Year"
Set_Pulses_Per_Rotation	"Invalid Pulses Per Rotation"
Set_CrossTalk	"Invalid CrossTalk"
Set_Number_of_Active_Channels	"Invalid Number Of Active Channels"
Set_Type_of_Calibration	"Invalid Type Of Calibration"
Set_Active_Page_Number	"Invalid Active Page Number"
Set_Destination_MAC_Address
Set_Destination_IP_Address
Set_Destination_Port_Number	"Invalid Port Number"
Set_Source_IP_Address
Set_Source_Port_Number	"Invalid Port Number"
Reset_Angle
Get Commands
Get_Offset_Value
Get_Fullscale_Value
Normal_Data_Request
Fast_Data_Request	"Invalid Firmware Version"
Version_of_Board
Reset_Board
Get_Display_Page
Get_Internal_Register	"Invalid Register"
Get_Data_Logging	"Invalid Counter"
Get_Rotation_Values
Get_Device_Count
Get_Device_Serial_Number
Get_Loading_Point	"Invalid Type Of Calibration" "Invalid Point"
Get_Offset_Load
Get_Load_of_Loading_Point	"Invalid Point"
Get_Fullscale_Load
Get_Number_of_Loading_Points
Get_Output_Type
Get_Sensitivity
Get_Bridge_Resistance
Get_ADC_PGA_Setting
Get_ADC_Sampling_Rate_Setting
Get_Sensor_Identification_Number
Get_Unit_Code
Get_Direction
Get_Shunt_Value
Get_Decimal_Point
Get_Calibration_Code
Get_Calibration_Day
Get_Calibration_Month
Get_Calibration_Year
Get_Pulses_Per_Rotation
Get_Voltage_Output
Get_CrossTalk
Get_Number_of_Active_Channels
Get_Type_of_Calibration
Get_Active_Page_Number
Get_Destination_MAC_Address
Get_Destination_IP_Address
Get_Destination_Port_Number
Get_Source_MAC_Address
Get_Source_IP_Address
Get_Source_Port_Number
Get_Excitation
Get_Analog_Voltage_Output
Get_Gain_Switch
Get_Polarity
Get_Shunt_Resistor
Get_Sensor_Sensitivity
Get_Zero_Potentiometer
Get_Span_1_Potentiometer
Get_Span_2_Potentiometer
Get_Average_Setting
Get_Type_of_Board
Get_Hardware_Version
Get_Firmware_Version
Get_Firmware_Year
Get_Firmware_Month
Backup Commands
Create_Back_Up	"Invalid Page Number"
Restore_Back_Up	"Invalid Page Number"
Control Commands
Change_Battery_Enter
Change_Tare_Up
Change_Display_Back
Change_Reset_Left
Change_Menu
Change_Unit_Right
Change_Shunt_Exit
Change_Hold_Down
Debugging Commands
Read_Memory_Register	"Invalid Address"
Write_Memory_Register	"Invalid Address" "Invalid Data"
Read_EEPROM_Register	"Invalid Address"
Write_EEPROM_Register	"Invalid Address" "Invalid High Byte" "Invalid Low Byte"
Read_TEDS_Register	"Invalid High Address" "Invalid Low Address"
Write_TEDS_Register	"Invalid Data" "Invalid High Address" "Invalid Low Address"
Read_Channel_Register	"Invalid Address"
Write_Channel_Register	"Invalid Address" "Invalid Data"
Read_Page_Register	"Invalid Page Number"